Source:Bb#
SCPI Commands
- [SOURce<HW>]:BB:CFACtor
- [SOURce<HW>]:BB:FOFFset
- [SOURce<HW>]:BB:IQGain
- [SOURce<HW>]:BB:MFPCorrection
- [SOURce<HW>]:BB:PGAin
- [SOURce<HW>]:BB:POFFset
- [SOURce<HW>]:BB:ROUTe
Cloning the Group
// Create a clone of the original group, that exists independently
var bb2 = driver.Source.Bb.Clone();
Direct SCPI Members
- double Cfactor#
// SCPI: [SOURce<HW>]:BB:CFACtor double value = driver.Source.Bb.Cfactor;Queries the crest factor of the baseband signal.
cfactor: float
- double Foffset#
// SCPI: [SOURce<HW>]:BB:FOFFset double value = driver.Source.Bb.Foffset; driver.Source.Bb.Foffset = 1.0;Sets a frequency offset for the internal or external baseband signal. The offset affects the generated baseband signal.
foffset: float
- IqGainAllEnum IqGain#
// SCPI: [SOURce<HW>]:BB:IQGain IqGainAllEnum value = driver.Source.Bb.IqGain; driver.Source.Bb.IqGain = IqGainAllEnum.AUTO;Sets the baseband gain for a wide dynamic range. You can amplify the baseband signal power level (positive gain) or attenuate this level (negative gain) to optimize the I/Q modulation performance. The optimization is a trade-off between signal distortion and signal-to-noise ratio (SNR) .
- double MfpCorrection#
// SCPI: [SOURce<HW>]:BB:MFPCorrection double value = driver.Source.Bb.MfpCorrection;No help available.
- double Pgain#
// SCPI: [SOURce<HW>]:BB:PGAin double value = driver.Source.Bb.Pgain; driver.Source.Bb.Pgain = 1.0;Sets the relative path gain for the selected baseband signal compared to the baseband signal of the other baseband sources. The gain affects the signal on the baseband block output. Applies for the other paths or the external baseband.
pgain: float
- double Poffset#
// SCPI: [SOURce<HW>]:BB:POFFset double value = driver.Source.Bb.Poffset; driver.Source.Bb.Poffset = 1.0;Sets the relative phase offset for the selected baseband signal. The latter applies for the other paths or the external baseband.
poffset: float
- PathUniCodBbinEnum Route#
// SCPI: [SOURce<HW>]:BB:ROUTe PathUniCodBbinEnum value = driver.Source.Bb.Route; driver.Source.Bb.Route = PathUniCodBbinEnum.A;Selects the signal route for the internal/external baseband signal. The internal and external signals are summed, if necessary.
route: A | B| AB
Subgroups
- Source:Bb:Arbitrary
- Source:Bb:Btooth
- Source:Bb:C2K
- Source:Bb:Coder
- Source:Bb:Dab
- Source:Bb:Dm
- Source:Bb:Dvb
- Source:Bb:Esequencer
- Source:Bb:Eutra
- Source:Bb:Evdo
- Source:Bb:Gbas
- Source:Bb:Gnpr
- Source:Bb:Gnss
- Source:Bb:Graphics
- Source:Bb:Gsm
- Source:Bb:Huwb
- Source:Bb:Impairment
- Source:Bb:Info
- Source:Bb:Kuiper
- Source:Bb:Lora
- Source:Bb:LrWpan
- Source:Bb:Mccw
- Source:Bb:Measurement
- Source:Bb:Nfc
- Source:Bb:Nr5G
- Source:Bb:Ofdm
- Source:Bb:Oneweb
- Source:Bb:Packet
- Source:Bb:Path
- Source:Bb:Power
- Source:Bb:Pramp
- Source:Bb:Progress
- Source:Bb:Tdscdma
- Source:Bb:Tetra
- Source:Bb:Trigger
- Source:Bb:V5G
- Source:Bb:W3Gpp
- Source:Bb:Wlad
- Source:Bb:Wlay
- Source:Bb:Wlnn