Mode

SCPI Command :

[SOURce<HW>]:BB:BTOoth:TRIGger:OUTPut<CH>:MODE

class ModeCls

Mode commands group definition. 1 total commands, 0 Subgroups, 1 group commands

get(output=Output.Default) → RsSmbv.enums.BtoMarkMode

# SCPI: [SOURce<HW>]:BB:BTOoth:TRIGger:OUTPut<CH>:MODE
value: enums.BtoMarkMode = driver.source.bb.btooth.trigger.output.mode.get(output = repcap.Output.Default)

Defines the signal for the selected marker output.

param output

optional repeated capability selector. Default value: Nr1 (settable in the interface ‘Output’)

return

mode: RESTart| STARt| ACTive| PULSe| PATTern| RATio | IACTive RESTart A marker signal is generated at the start of each signal sequence. STARt A marker signal is generated at the start of each event/frame. ACTive The marker masks the active part of the event/frame. At the start of each burst, the marker signal changes to high. It changes back to low after the end of each burst. PULSe A regular marker signal is generated. The clock frequency is defined by entering a divider. The frequency is derived by dividing the symbol rate by the divider. The input box for divider opens when ‘Pulse’ is selected, and the resulting pulse frequency is displayed below. PATTern A marker signal that is defined by a bit pattern is generated. The pattern has a maximum length of 32 bits and is defined in an input field which opens when pattern is selected. RATio A regular marker signal corresponding to the ‘Time Off’ / ‘Time On’ specifications in the commands SOURce1:BB:BTO:TRIGger:OUTPut:OFFTime and SOURce1:BB:BTO:TRIGger:OUTPut:ONTime is generated. IACTive The marker masks the inactive part of the event/frame. At the start of each burst, the marker signal changes to low. It changes back to high after the end of each burst.

set(mode: RsSmbv.enums.BtoMarkMode, output=Output.Default) → None

# SCPI: [SOURce<HW>]:BB:BTOoth:TRIGger:OUTPut<CH>:MODE
driver.source.bb.btooth.trigger.output.mode.set(mode = enums.BtoMarkMode.ACTive, output = repcap.Output.Default)

Defines the signal for the selected marker output.

param mode

RESTart| STARt| ACTive| PULSe| PATTern| RATio | IACTive RESTart A marker signal is generated at the start of each signal sequence. STARt A marker signal is generated at the start of each event/frame. ACTive The marker masks the active part of the event/frame. At the start of each burst, the marker signal changes to high. It changes back to low after the end of each burst. PULSe A regular marker signal is generated. The clock frequency is defined by entering a divider. The frequency is derived by dividing the symbol rate by the divider. The input box for divider opens when ‘Pulse’ is selected, and the resulting pulse frequency is displayed below. PATTern A marker signal that is defined by a bit pattern is generated. The pattern has a maximum length of 32 bits and is defined in an input field which opens when pattern is selected. RATio A regular marker signal corresponding to the ‘Time Off’ / ‘Time On’ specifications in the commands SOURce1:BB:BTO:TRIGger:OUTPut:OFFTime and SOURce1:BB:BTO:TRIGger:OUTPut:ONTime is generated. IACTive The marker masks the inactive part of the event/frame. At the start of each burst, the marker signal changes to low. It changes back to high after the end of each burst.

param output

optional repeated capability selector. Default value: Nr1 (settable in the interface ‘Output’)