Gs
SCPI Commands :
[SOURce<HW>]:BB:EUTRa:TCW:GS:ANTSubset
[SOURce<HW>]:BB:EUTRa:TCW:GS:BSCLass
[SOURce<HW>]:BB:EUTRa:TCW:GS:GENSignals
[SOURce<HW>]:BB:EUTRa:TCW:GS:INSTsetup
[SOURce<HW>]:BB:EUTRa:TCW:GS:MARKerconfig
[SOURce<HW>]:BB:EUTRa:TCW:GS:MODE
[SOURce<HW>]:BB:EUTRa:TCW:GS:OPTion
[SOURce<HW>]:BB:EUTRa:TCW:GS:RELease
[SOURce<HW>]:BB:EUTRa:TCW:GS:RXANtennas
[SOURce<HW>]:BB:EUTRa:TCW:GS:SIGRout
[SOURce<HW>]:BB:EUTRa:TCW:GS:SPEC
[SOURce<HW>]:BB:EUTRa:TCW:GS:STC
[SOURce<HW>]:BB:EUTRa:TCW:GS:TRIGgerconfig
[SOURce<HW>]:BB:EUTRa:TCW:GS:TXANtennas
- class GsCls[source]
Gs commands group definition. 14 total commands, 0 Subgroups, 14 group commands
- get_ant_subset() EutraTcwaNtSubset [source]
# SCPI: [SOURce<HW>]:BB:EUTRa:TCW:GS:ANTSubset value: enums.EutraTcwaNtSubset = driver.source.bb.eutra.tcw.gs.get_ant_subset()
Enabled for test setups with eight Rx antennas Determines the signal of which antenna couple, Antenna 1 and 2 (AS12) , Antenna 3 and 4 (AS34) , Antenna 5 and 6 (AS56) or Antenna 7 and 8 (AS78) , is generated by the instrument.
- return:
antenna_subset: AS34| AS12| ALL| AS56| AS78
- get_bs_class() UtraTcwbSclass [source]
# SCPI: [SOURce<HW>]:BB:EUTRa:TCW:GS:BSCLass value: enums.UtraTcwbSclass = driver.source.bb.eutra.tcw.gs.get_bs_class()
Sets the base station class.
- return:
bs_class: WIDE| LOCal| HOME| MEDium
- get_gen_signals() EutraTcwGeneratedSig [source]
# SCPI: [SOURce<HW>]:BB:EUTRa:TCW:GS:GENSignals value: enums.EutraTcwGeneratedSig = driver.source.bb.eutra.tcw.gs.get_gen_signals()
Determines the signal generated by the instrument.
- return:
generated_signal: WSIF1AWGN| IF23| ALL| WSUE1UE2AWGN| WSUE3UE4| IF WSIF1AWGN Wanted Signal, Interferer 1 and AWGN only; required in test setup with two instruments IF23 Interferes 2 and 3 only; required in test setup with two instruments ALL The instrument generates all required signals WSUE1UE2AWGN Only Wanted Signal UE 1, Wanted Signal UE 2 and AWGN WSUE3UE4 Only Wanted Signal UE 3 and Wanted Signal UE 4 IF Interferer signal only
- get_inst_setup() EutraTcwiNstSetup [source]
# SCPI: [SOURce<HW>]:BB:EUTRa:TCW:GS:INSTsetup value: enums.EutraTcwiNstSetup = driver.source.bb.eutra.tcw.gs.get_inst_setup()
Determines whether one or both paths are used.
- return:
instrument_setup: U2PATH| U1PATH
- get_marker_config() EutraTcwMarkConf [source]
# SCPI: [SOURce<HW>]:BB:EUTRa:TCW:GS:MARKerconfig value: enums.EutraTcwMarkConf = driver.source.bb.eutra.tcw.gs.get_marker_config()
Selects the marker configuration. The marker can be used to synchronize the measuring equipment to the signal generator.
- return:
marker_config: UNCHanged| FRAMe FRAMe The marker settings are customized for the selected test case. ‘Radio Frame Start’ markers are output; the marker delays are set equal to zero. UNCHanged The current marker settings of the signal generator are retained unchanged.
- get_mode() EutraTcwGsModeDefaultRange [source]
# SCPI: [SOURce<HW>]:BB:EUTRa:TCW:GS:MODE value: enums.EutraTcwGsModeDefaultRange = driver.source.bb.eutra.tcw.gs.get_mode()
Determines the measurements type, Pfa or Pd, the signal is generated for, see ‘Mode’.
- return:
mode: DRATe| FDRate| ADRate FDRate False Detection Rate (Pfa) DRATe Detection Rate (Pd) ADRate Alternating Pd and Pfa
- get_option() UtraTcwgsoPtion [source]
# SCPI: [SOURce<HW>]:BB:EUTRa:TCW:GS:OPTion value: enums.UtraTcwgsoPtion = driver.source.bb.eutra.tcw.gs.get_option()
Selects one of the two test case options.
- return:
option: OPT1| OPT2
- get_release() EutraTcwRelease [source]
# SCPI: [SOURce<HW>]:BB:EUTRa:TCW:GS:RELease value: enums.EutraTcwRelease = driver.source.bb.eutra.tcw.gs.get_release()
Sets the 3GPP test specification used as a guideline for the test cases.
- return:
release: REL8| REL9| REL10| REL11 | REL12| REL13TO15
- get_rx_antennas() EutraTcwNumOfRxAnt [source]
# SCPI: [SOURce<HW>]:BB:EUTRa:TCW:GS:RXANtennas value: enums.EutraTcwNumOfRxAnt = driver.source.bb.eutra.tcw.gs.get_rx_antennas()
For performance requirement tests, determines the number of the Rx antennas.
- return:
num_of_rx_antennas: ANT4| ANT2| ANT1
- get_sig_rout() EutraTcwSignalRout [source]
# SCPI: [SOURce<HW>]:BB:EUTRa:TCW:GS:SIGRout value: enums.EutraTcwSignalRout = driver.source.bb.eutra.tcw.gs.get_sig_rout()
Selects the signal routing for baseband A signal which usually represents the wanted signal.
- return:
signal_routing: PORTA | PORTB
- get_spec() UtraTcwsPec [source]
# SCPI: [SOURce<HW>]:BB:EUTRa:TCW:GS:SPEC value: enums.UtraTcwsPec = driver.source.bb.eutra.tcw.gs.get_spec()
Selects the 3GPP test specification used as a guideline for the test cases.
- return:
gs_spec: TS36141
- get_stc() UtraTcwgssUbtest [source]
# SCPI: [SOURce<HW>]:BB:EUTRa:TCW:GS:STC value: enums.UtraTcwgssUbtest = driver.source.bb.eutra.tcw.gs.get_stc()
Selects the subtest case.
- return:
sub_test_case: STC1| STC2| STC4| STC3
- get_trigger_config() EutraTcwtRigConf [source]
# SCPI: [SOURce<HW>]:BB:EUTRa:TCW:GS:TRIGgerconfig value: enums.EutraTcwtRigConf = driver.source.bb.eutra.tcw.gs.get_trigger_config()
Selects the trigger configuration. The trigger is used to synchronize the signal generator to the other equipment.
- return:
trigger_config: UNCHanged| AAUTo UNCHanged The current trigger settings of the signal generator are retained unchanged. AAUTo The trigger settings are customized for the selected test case. The trigger setting ‘Armed Auto’ with external trigger source is used; the trigger delay is set to zero. Thus, the base station frame timing is able to synchronize the signal generator by a periodic trigger.
- get_tx_antennas() TxAntenna [source]
# SCPI: [SOURce<HW>]:BB:EUTRa:TCW:GS:TXANtennas value: enums.TxAntenna = driver.source.bb.eutra.tcw.gs.get_tx_antennas()
For performance requirement tests, determines the number of the Tx antennas.
- return:
num_of_tx_antennas: ANT1| ANT2
- set_ant_subset(antenna_subset: EutraTcwaNtSubset) None [source]
# SCPI: [SOURce<HW>]:BB:EUTRa:TCW:GS:ANTSubset driver.source.bb.eutra.tcw.gs.set_ant_subset(antenna_subset = enums.EutraTcwaNtSubset.ALL)
Enabled for test setups with eight Rx antennas Determines the signal of which antenna couple, Antenna 1 and 2 (AS12) , Antenna 3 and 4 (AS34) , Antenna 5 and 6 (AS56) or Antenna 7 and 8 (AS78) , is generated by the instrument.
- param antenna_subset:
AS34| AS12| ALL| AS56| AS78
- set_bs_class(bs_class: UtraTcwbSclass) None [source]
# SCPI: [SOURce<HW>]:BB:EUTRa:TCW:GS:BSCLass driver.source.bb.eutra.tcw.gs.set_bs_class(bs_class = enums.UtraTcwbSclass.HOME)
Sets the base station class.
- param bs_class:
WIDE| LOCal| HOME| MEDium
- set_gen_signals(generated_signal: EutraTcwGeneratedSig) None [source]
# SCPI: [SOURce<HW>]:BB:EUTRa:TCW:GS:GENSignals driver.source.bb.eutra.tcw.gs.set_gen_signals(generated_signal = enums.EutraTcwGeneratedSig.ALL)
Determines the signal generated by the instrument.
- param generated_signal:
WSIF1AWGN| IF23| ALL| WSUE1UE2AWGN| WSUE3UE4| IF WSIF1AWGN Wanted Signal, Interferer 1 and AWGN only; required in test setup with two instruments IF23 Interferes 2 and 3 only; required in test setup with two instruments ALL The instrument generates all required signals WSUE1UE2AWGN Only Wanted Signal UE 1, Wanted Signal UE 2 and AWGN WSUE3UE4 Only Wanted Signal UE 3 and Wanted Signal UE 4 IF Interferer signal only
- set_inst_setup(instrument_setup: EutraTcwiNstSetup) None [source]
# SCPI: [SOURce<HW>]:BB:EUTRa:TCW:GS:INSTsetup driver.source.bb.eutra.tcw.gs.set_inst_setup(instrument_setup = enums.EutraTcwiNstSetup.U1PATH)
Determines whether one or both paths are used.
- param instrument_setup:
U2PATH| U1PATH
- set_marker_config(marker_config: EutraTcwMarkConf) None [source]
# SCPI: [SOURce<HW>]:BB:EUTRa:TCW:GS:MARKerconfig driver.source.bb.eutra.tcw.gs.set_marker_config(marker_config = enums.EutraTcwMarkConf.FRAMe)
Selects the marker configuration. The marker can be used to synchronize the measuring equipment to the signal generator.
- param marker_config:
UNCHanged| FRAMe FRAMe The marker settings are customized for the selected test case. ‘Radio Frame Start’ markers are output; the marker delays are set equal to zero. UNCHanged The current marker settings of the signal generator are retained unchanged.
- set_mode(mode: EutraTcwGsModeDefaultRange) None [source]
# SCPI: [SOURce<HW>]:BB:EUTRa:TCW:GS:MODE driver.source.bb.eutra.tcw.gs.set_mode(mode = enums.EutraTcwGsModeDefaultRange.ADRate)
Determines the measurements type, Pfa or Pd, the signal is generated for, see ‘Mode’.
- param mode:
DRATe| FDRate| ADRate FDRate False Detection Rate (Pfa) DRATe Detection Rate (Pd) ADRate Alternating Pd and Pfa
- set_option(option: UtraTcwgsoPtion) None [source]
# SCPI: [SOURce<HW>]:BB:EUTRa:TCW:GS:OPTion driver.source.bb.eutra.tcw.gs.set_option(option = enums.UtraTcwgsoPtion.OPT1)
Selects one of the two test case options.
- param option:
OPT1| OPT2
- set_release(release: EutraTcwRelease) None [source]
# SCPI: [SOURce<HW>]:BB:EUTRa:TCW:GS:RELease driver.source.bb.eutra.tcw.gs.set_release(release = enums.EutraTcwRelease.REL10)
Sets the 3GPP test specification used as a guideline for the test cases.
- param release:
REL8| REL9| REL10| REL11 | REL12| REL13TO15
- set_rx_antennas(num_of_rx_antennas: EutraTcwNumOfRxAnt) None [source]
# SCPI: [SOURce<HW>]:BB:EUTRa:TCW:GS:RXANtennas driver.source.bb.eutra.tcw.gs.set_rx_antennas(num_of_rx_antennas = enums.EutraTcwNumOfRxAnt.ANT1)
For performance requirement tests, determines the number of the Rx antennas.
- param num_of_rx_antennas:
ANT4| ANT2| ANT1
- set_sig_rout(signal_routing: EutraTcwSignalRout) None [source]
# SCPI: [SOURce<HW>]:BB:EUTRa:TCW:GS:SIGRout driver.source.bb.eutra.tcw.gs.set_sig_rout(signal_routing = enums.EutraTcwSignalRout.PORTA)
Selects the signal routing for baseband A signal which usually represents the wanted signal.
- param signal_routing:
PORTA | PORTB
- set_spec(gs_spec: UtraTcwsPec) None [source]
# SCPI: [SOURce<HW>]:BB:EUTRa:TCW:GS:SPEC driver.source.bb.eutra.tcw.gs.set_spec(gs_spec = enums.UtraTcwsPec.TS36141)
Selects the 3GPP test specification used as a guideline for the test cases.
- param gs_spec:
TS36141
- set_stc(sub_test_case: UtraTcwgssUbtest) None [source]
# SCPI: [SOURce<HW>]:BB:EUTRa:TCW:GS:STC driver.source.bb.eutra.tcw.gs.set_stc(sub_test_case = enums.UtraTcwgssUbtest.STC1)
Selects the subtest case.
- param sub_test_case:
STC1| STC2| STC4| STC3
- set_trigger_config(trigger_config: EutraTcwtRigConf) None [source]
# SCPI: [SOURce<HW>]:BB:EUTRa:TCW:GS:TRIGgerconfig driver.source.bb.eutra.tcw.gs.set_trigger_config(trigger_config = enums.EutraTcwtRigConf.AAUTo)
Selects the trigger configuration. The trigger is used to synchronize the signal generator to the other equipment.
- param trigger_config:
UNCHanged| AAUTo UNCHanged The current trigger settings of the signal generator are retained unchanged. AAUTo The trigger settings are customized for the selected test case. The trigger setting ‘Armed Auto’ with external trigger source is used; the trigger delay is set to zero. Thus, the base station frame timing is able to synchronize the signal generator by a periodic trigger.
- set_tx_antennas(num_of_tx_antennas: TxAntenna) None [source]
# SCPI: [SOURce<HW>]:BB:EUTRa:TCW:GS:TXANtennas driver.source.bb.eutra.tcw.gs.set_tx_antennas(num_of_tx_antennas = enums.TxAntenna.ANT1)
For performance requirement tests, determines the number of the Tx antennas.
- param num_of_tx_antennas:
ANT1| ANT2