Source:Bb:Nr5G:Tcw:Ws#

SCPI Commands

[SOURce<HW>]:BB:NR5G:TCW:WS:CBW
[SOURce<HW>]:BB:NR5G:TCW:WS:CELLid
[SOURce<HW>]:BB:NR5G:TCW:WS:DUPLex
[SOURce<HW>]:BB:NR5G:TCW:WS:FMTHroughput
[SOURce<HW>]:BB:NR5G:TCW:WS:FROFfset
[SOURce<HW>]:BB:NR5G:TCW:WS:MAPType
[SOURce<HW>]:BB:NR5G:TCW:WS:MODE
[SOURce<HW>]:BB:NR5G:TCW:WS:PLEVel
[SOURce<HW>]:BB:NR5G:TCW:WS:PROCondition
[SOURce<HW>]:BB:NR5G:TCW:WS:RBOFfset
[SOURce<HW>]:BB:NR5G:TCW:WS:RFFRequency
[SOURce<HW>]:BB:NR5G:TCW:WS:RSET
[SOURce<HW>]:BB:NR5G:TCW:WS:SCSPacing
[SOURce<HW>]:BB:NR5G:TCW:WS:SYMNumber
[SOURce<HW>]:BB:NR5G:TCW:WS:TAPos
[SOURce<HW>]:BB:NR5G:TCW:WS:TIOBase
[SOURce<HW>]:BB:NR5G:TCW:WS:TREQuire
[SOURce<HW>]:BB:NR5G:TCW:WS:TSETup
[SOURce<HW>]:BB:NR5G:TCW:WS:UEID
[SOURce<HW>]:BB:NR5G:TCW:WS:VDRF

Cloning the Group

// Create a clone of the original group, that exists independently
var ws2 = driver.Source.Bb.Nr5G.Tcw.Ws.Clone();

Direct SCPI Members

Nr5GcbwEnum Cbw#
// SCPI: [SOURce<HW>]:BB:NR5G:TCW:WS:CBW
Nr5GcbwEnum value = driver.Source.Bb.Nr5G.Tcw.Ws.Cbw;
driver.Source.Bb.Nr5G.Tcw.Ws.Cbw = Nr5GcbwEnum.BW10;

Selects the channel bandwidth.

wsChBw: Bandwidth in MHz


int CellId#
// SCPI: [SOURce<HW>]:BB:NR5G:TCW:WS:CELLid
int value = driver.Source.Bb.Nr5G.Tcw.Ws.CellId;
driver.Source.Bb.Nr5G.Tcw.Ws.CellId = 1;

Sets the cell ID.

wsCellId: integer


EutraDuplexModeEnum Duplex#
// SCPI: [SOURce<HW>]:BB:NR5G:TCW:WS:DUPLex
EutraDuplexModeEnum value = driver.Source.Bb.Nr5G.Tcw.Ws.Duplex;
driver.Source.Bb.Nr5G.Tcw.Ws.Duplex = EutraDuplexModeEnum.FDD;

The duplexing mechanism used can be switched between FDD and TDD.

duplexing: FDD | TDD


EutraTcwfRactMaxThroughputEnum FmThroughput#
// SCPI: [SOURce<HW>]:BB:NR5G:TCW:WS:FMTHroughput
EutraTcwfRactMaxThroughputEnum value = driver.Source.Bb.Nr5G.Tcw.Ws.FmThroughput;
driver.Source.Bb.Nr5G.Tcw.Ws.FmThroughput = EutraTcwfRactMaxThroughputEnum.FMT30;

The required throughput is expressed as a fraction of maximum throughput for the FRC. The performance requirements assume HARQ retransmissions. The throughput shall be equal to or larger than the fraction of maximum throughput for the FRCs at the given SNR.

fmt: FMT70 | FMT30


FreqOffsetEnum FrOffset#
// SCPI: [SOURce<HW>]:BB:NR5G:TCW:WS:FROFfset
FreqOffsetEnum value = driver.Source.Bb.Nr5G.Tcw.Ws.FrOffset;
driver.Source.Bb.Nr5G.Tcw.Ws.FrOffset = FreqOffsetEnum.FO_0;

Sets the frequency offset used for the PRACH.

freqOffset: FO_0 | FO_400 | FO_4000 | FO_625 | FO_1340 | FO_1740 | FO_2334 | FO_3334 | FO_19444


MappingTypeEnum MapType#
// SCPI: [SOURce<HW>]:BB:NR5G:TCW:WS:MAPType
MappingTypeEnum value = driver.Source.Bb.Nr5G.Tcw.Ws.MapType;
driver.Source.Bb.Nr5G.Tcw.Ws.MapType = MappingTypeEnum.A;

Sets the mapping type A or B for the PUSCH.

mapType: A | B


ModeEnum Mode#
// SCPI: [SOURce<HW>]:BB:NR5G:TCW:WS:MODE
ModeEnum value = driver.Source.Bb.Nr5G.Tcw.Ws.Mode;
driver.Source.Bb.Nr5G.Tcw.Ws.Mode = ModeEnum.DRAT;

Switches between the detection rate (Pd) and the false detection rate (Pfa) .

mode: DRAT | FDR

  • DRAT: Pd is defined as the probability of detection of preamble.

  • FDR: Pfa is defined as the total probability of false detection of the preamble.


double Plevel#
// SCPI: [SOURce<HW>]:BB:NR5G:TCW:WS:PLEVel
double value = driver.Source.Bb.Nr5G.Tcw.Ws.Plevel;
driver.Source.Bb.Nr5G.Tcw.Ws.Plevel = 1.0;

Specifies the power level of the wanted signal.

wsPowLev: float


PropagCondEnum ProCondition#
// SCPI: [SOURce<HW>]:BB:NR5G:TCW:WS:PROCondition
PropagCondEnum value = driver.Source.Bb.Nr5G.Tcw.Ws.ProCondition;
driver.Source.Bb.Nr5G.Tcw.Ws.ProCondition = PropagCondEnum.AWGN;

The propagation conditions define the multipath fading environment. They indicated as a combination of channel model name and maximum Doppler frequency, i.e. TDLA<DS>-<Doppler> where <DS> indicates the desired delay spread and <Doppler> indicates the maximum Doppler frequency.

propagCond: TDLB100D400 | TDLC300D100 | TDLA30D10 | AWGN | TDLA30D300 | TDLA30D75 | HST1NR350 | HST3NR350 | HST1NR500 | HST3NR500 | TDLC300D600 | TDLC300D1200 | MPX | MPY | MPZ


int RbOffset#
// SCPI: [SOURce<HW>]:BB:NR5G:TCW:WS:RBOFfset
int value = driver.Source.Bb.Nr5G.Tcw.Ws.RbOffset;
driver.Source.Bb.Nr5G.Tcw.Ws.RbOffset = 1;

Sets the resource block offset of the wanted signal.

wsRbOffset: Number of resource blocks.


int RfFrequency#
// SCPI: [SOURce<HW>]:BB:NR5G:TCW:WS:RFFRequency
int value = driver.Source.Bb.Nr5G.Tcw.Ws.RfFrequency;
driver.Source.Bb.Nr5G.Tcw.Ws.RfFrequency = 1;

Sets the RF frequency of the wanted signal.

wsRfFreq: integer


RestrictedSetEnum Rset#
// SCPI: [SOURce<HW>]:BB:NR5G:TCW:WS:RSET
RestrictedSetEnum value = driver.Source.Bb.Nr5G.Tcw.Ws.Rset;
driver.Source.Bb.Nr5G.Tcw.Ws.Rset = RestrictedSetEnum.ARES;

Selects the restricted set type for the PRACH. Prerequisites for this command

  • Select high speed train mode .

  • Select preamble format 0 .

restrictedSet: ARES | BRES

  • ARES: Restricted set type A.

  • BRES: Restricted set type B.


NumerologyEnum ScSpacing#
// SCPI: [SOURce<HW>]:BB:NR5G:TCW:WS:SCSPacing
NumerologyEnum value = driver.Source.Bb.Nr5G.Tcw.Ws.ScSpacing;
driver.Source.Bb.Nr5G.Tcw.Ws.ScSpacing = NumerologyEnum.N120;

Sets the subcarrier spacing.

wsSubcarSpacing: N15 | N30 | N60 | X60 | N120 | N240 | N480 | N960

  • N15, N30, N60, N120, N240, N480, N960: Normal cyclic prefix, value in kHz

  • E60: Extended cyclic prefix, 60 kHz


int SymNumber#
// SCPI: [SOURce<HW>]:BB:NR5G:TCW:WS:SYMNumber
int value = driver.Source.Bb.Nr5G.Tcw.Ws.SymNumber;
driver.Source.Bb.Nr5G.Tcw.Ws.SymNumber = 1;

Sets the number of used OFDM symbols. The starting symbol index is 13 for 1 OFDM symbol and 12 for 2 OFDM symbols.

symbolNumber: integer


int Tapos#
// SCPI: [SOURce<HW>]:BB:NR5G:TCW:WS:TAPos
int value = driver.Source.Bb.Nr5G.Tcw.Ws.Tapos;
driver.Source.Bb.Nr5G.Tcw.Ws.Tapos = 1;

Sets the position of first DM-RS symbol for PUSCH (and PDSCH) mapping type A (dmrs-TypeA-Position) .

wsTypeaPos: integer


double TioBase#
// SCPI: [SOURce<HW>]:BB:NR5G:TCW:WS:TIOBase
double value = driver.Source.Bb.Nr5G.Tcw.Ws.TioBase;

Queries the timing off base value.

timingOffsetBase: float


TestRequirmentEnum Trequire#
// SCPI: [SOURce<HW>]:BB:NR5G:TCW:WS:TREQuire
TestRequirmentEnum value = driver.Source.Bb.Nr5G.Tcw.Ws.Trequire;
driver.Source.Bb.Nr5G.Tcw.Ws.Trequire = TestRequirmentEnum.HST;

Selects the test requirement for 3GPP test cases.

testRequirement: NORM | HST


TestSetupEnum Tsetup#
// SCPI: [SOURce<HW>]:BB:NR5G:TCW:WS:TSETup
TestSetupEnum value = driver.Source.Bb.Nr5G.Tcw.Ws.Tsetup;
driver.Source.Bb.Nr5G.Tcw.Ws.Tsetup = TestSetupEnum.TS_1;

With the test setup selector, the signal definitions can be switched.

testSetup: TS_1 | TS_2


int UeId#
// SCPI: [SOURce<HW>]:BB:NR5G:TCW:WS:UEID
int value = driver.Source.Bb.Nr5G.Tcw.Ws.UeId;
driver.Source.Bb.Nr5G.Tcw.Ws.UeId = 1;

Sets the UE ID.

wsUeid: integer


int Vdrf#
// SCPI: [SOURce<HW>]:BB:NR5G:TCW:WS:VDRF
int value = driver.Source.Bb.Nr5G.Tcw.Ws.Vdrf;
driver.Source.Bb.Nr5G.Tcw.Ws.Vdrf = 1;

Sets the virtual downlink RF frequency

virtualDlRf: integer


Subgroups