Source:Bb:Nr5G:Tcw:Rtf#

SCPI Commands

[SOURce<HW>]:BB:NR5G:TCW:RTF:AUSDelay
[SOURce<HW>]:BB:NR5G:TCW:RTF:BBSelector
[SOURce<HW>]:BB:NR5G:TCW:RTF:CONNector
[SOURce<HW>]:BB:NR5G:TCW:RTF:CSRate
[SOURce<HW>]:BB:NR5G:TCW:RTF:MODE
[SOURce<HW>]:BB:NR5G:TCW:RTF:SERRate

Cloning the Group

// Create a clone of the original group, that exists independently
var rtf2 = driver.Source.Bb.Nr5G.Tcw.Rtf.Clone();

Direct SCPI Members

double AusDelay#
// SCPI: [SOURce<HW>]:BB:NR5G:TCW:RTF:AUSDelay
double value = driver.Source.Bb.Nr5G.Tcw.Rtf.AusDelay;
driver.Source.Bb.Nr5G.Tcw.Rtf.AusDelay = 1.0;

Defines the delay added to the real-time feedback.

addUserDelay: float


int BbSelector#
// SCPI: [SOURce<HW>]:BB:NR5G:TCW:RTF:BBSelector
int value = driver.Source.Bb.Nr5G.Tcw.Rtf.BbSelector;
driver.Source.Bb.Nr5G.Tcw.Rtf.BbSelector = 1;

Defines which baseband selector index is used in the serial messages to address the baseband. For some test case that test a moving UE, the command sets the connector of the moving UE.

bbSelector: integer


FeedbackConnectorAllEnum Connector#
// SCPI: [SOURce<HW>]:BB:NR5G:TCW:RTF:CONNector
FeedbackConnectorAllEnum value = driver.Source.Bb.Nr5G.Tcw.Rtf.Connector;
driver.Source.Bb.Nr5G.Tcw.Rtf.Connector = FeedbackConnectorAllEnum.LOCal;

Queries the connector used for the real-time feedback. For some test case that test a moving UE, the command queries the connector of the moving UE. Note that the result of the query is always LOCal, because feedback always uses the local connector.

connector: LOCal


int CsRate#
// SCPI: [SOURce<HW>]:BB:NR5G:TCW:RTF:CSRate
int value = driver.Source.Bb.Nr5G.Tcw.Rtf.CsRate;
driver.Source.Bb.Nr5G.Tcw.Rtf.CsRate = 1;

Defines a custom serial rate. Prerequisites for this command

  • Select a custom serial rate .


TcwfEedbackModeEnum Mode#
// SCPI: [SOURce<HW>]:BB:NR5G:TCW:RTF:MODE
TcwfEedbackModeEnum value = driver.Source.Bb.Nr5G.Tcw.Rtf.Mode;
driver.Source.Bb.Nr5G.Tcw.Rtf.Mode = TcwfEedbackModeEnum.ETH;

Selects the serial line mode used for the real-time feedback.

  • ETH: Ethernet feedback mode.You can define the network characteristics with the commands listed in “Real-time feedback”.

  • SERial: Serial feedback mode.

  • S3X8: Serial 3x8 feedback mode.


FeedbackRateAllEnum SerRate#
// SCPI: [SOURce<HW>]:BB:NR5G:TCW:RTF:SERRate
FeedbackRateAllEnum value = driver.Source.Bb.Nr5G.Tcw.Rtf.SerRate;
driver.Source.Bb.Nr5G.Tcw.Rtf.SerRate = FeedbackRateAllEnum.CUST;

Sets the bit rate of the serial transmission. For test cases with high subcarrier spacing (SCS) and short slot duration, a serial rate of 115.2 kbps is insufficient. We recommend that you use higher serial rate so that at least one feedback command per slot is received.

  • R115 | R1M6 | R1M9: 115.2 kbps, 1.6 Mbps, 1.92 Mbps

  • CUST: Custom serial rate. You can define the serial rate with [:SOURcehw]:BB:NR5G:TCW:RTF:CSRate.


Subgroups