Source:Bb:Eutra:Tcw:Rtf#

SCPI Commands

[SOURce<HW>]:BB:EUTRa:TCW:RTF:ACKDefinition
[SOURce<HW>]:BB:EUTRa:TCW:RTF:AUSDelay
[SOURce<HW>]:BB:EUTRa:TCW:RTF:BBSMue
[SOURce<HW>]:BB:EUTRa:TCW:RTF:BBSSue
[SOURce<HW>]:BB:EUTRa:TCW:RTF:BBSelector
[SOURce<HW>]:BB:EUTRa:TCW:RTF:CONMue
[SOURce<HW>]:BB:EUTRa:TCW:RTF:CONNector
[SOURce<HW>]:BB:EUTRa:TCW:RTF:CONSue
[SOURce<HW>]:BB:EUTRa:TCW:RTF:MODE
[SOURce<HW>]:BB:EUTRa:TCW:RTF:SERRate

Direct SCPI Members

LowHighEnum AckDefinition#
// SCPI: [SOURce<HW>]:BB:EUTRa:TCW:RTF:ACKDefinition
LowHighEnum value = driver.Source.Bb.Eutra.Tcw.Rtf.AckDefinition;
driver.Source.Bb.Eutra.Tcw.Rtf.AckDefinition = LowHighEnum.HIGH;

Determines whether a high or a low binary level on the feedback line connector represents an ACK.

ackDefinition: LOW | HIGH


double AusDelay#
// SCPI: [SOURce<HW>]:BB:EUTRa:TCW:RTF:AUSDelay
double value = driver.Source.Bb.Eutra.Tcw.Rtf.AusDelay;
driver.Source.Bb.Eutra.Tcw.Rtf.AusDelay = 1.0;

Determines the point in time when the feedback can be sent to the instrument.

addUserDelay: float


int BbSmue#
// SCPI: [SOURce<HW>]:BB:EUTRa:TCW:RTF:BBSMue
int value = driver.Source.Bb.Eutra.Tcw.Rtf.BbSmue;
driver.Source.Bb.Eutra.Tcw.Rtf.BbSmue = 1;

This parameter is required for multiplexing serial commands for different baseband units to one feedback line. If the selector n is configured in the GUI for a specific baseband unit, the baseband unit will listen only to serial commands containing the selector n.


int BbSsue#
// SCPI: [SOURce<HW>]:BB:EUTRa:TCW:RTF:BBSSue
int value = driver.Source.Bb.Eutra.Tcw.Rtf.BbSsue;
driver.Source.Bb.Eutra.Tcw.Rtf.BbSsue = 1;

This parameter is required for multiplexing serial commands for different baseband units to one feedback line. If the selector n is configured in the GUI for a specific baseband unit, the baseband unit will listen only to serial commands containing the selector n.


int BbSelector#
// SCPI: [SOURce<HW>]:BB:EUTRa:TCW:RTF:BBSelector
int value = driver.Source.Bb.Eutra.Tcw.Rtf.BbSelector;
driver.Source.Bb.Eutra.Tcw.Rtf.BbSelector = 1;

This parameter is required for multiplexing serial commands for different baseband units to one feedback line. If the selector n is configured in the GUI for a specific baseband unit, the baseband unit will listen only to serial commands containing the selector n.

bbSelector: integer


EutraTcwConnectorEnum Conmue#
// SCPI: [SOURce<HW>]:BB:EUTRa:TCW:RTF:CONMue
EutraTcwConnectorEnum value = driver.Source.Bb.Eutra.Tcw.Rtf.Conmue;
driver.Source.Bb.Eutra.Tcw.Rtf.Conmue = EutraTcwConnectorEnum.GLOBal;

Determines the feedback line connector.


EutraTcwConnectorEnum Connector#
// SCPI: [SOURce<HW>]:BB:EUTRa:TCW:RTF:CONNector
EutraTcwConnectorEnum value = driver.Source.Bb.Eutra.Tcw.Rtf.Connector;
driver.Source.Bb.Eutra.Tcw.Rtf.Connector = EutraTcwConnectorEnum.GLOBal;

Determines the feedback line connector.

connector: NOFB | LOCal | GLOBal


EutraTcwConnectorEnum Consue#
// SCPI: [SOURce<HW>]:BB:EUTRa:TCW:RTF:CONSue
EutraTcwConnectorEnum value = driver.Source.Bb.Eutra.Tcw.Rtf.Consue;
driver.Source.Bb.Eutra.Tcw.Rtf.Consue = EutraTcwConnectorEnum.GLOBal;

Determines the feedback line connector.


EutraTcwrtfModeEnum Mode#
// SCPI: [SOURce<HW>]:BB:EUTRa:TCW:RTF:MODE
EutraTcwrtfModeEnum value = driver.Source.Bb.Eutra.Tcw.Rtf.Mode;
driver.Source.Bb.Eutra.Tcw.Rtf.Mode = EutraTcwrtfModeEnum.BIN;

Determines the feedback mode.

mode: SER3X8 | SER | BIN

  • BIN: Binary ACK/NACK

  • SER: Serial

  • SER3X8: Serial 3x8


EutraSerialRateEnum SerRate#
// SCPI: [SOURce<HW>]:BB:EUTRa:TCW:RTF:SERRate
EutraSerialRateEnum value = driver.Source.Bb.Eutra.Tcw.Rtf.SerRate;
driver.Source.Bb.Eutra.Tcw.Rtf.SerRate = EutraSerialRateEnum.SR1_6M;

Sets the bit rate of the serial transmission. Possible rates are 115.2 kbps, 1.6 Mbps and 1.92 Mbps.

serialRate: SR1_92M | SR1_6M | SR115_2K