Source:Bb:Btooth:DtTest#

SCPI Commands

[SOURce<HW>]:BB:BTOoth:DTTest:DIRft
[SOURce<HW>]:BB:BTOoth:DTTest:DTTState
[SOURce<HW>]:BB:BTOoth:DTTest:FDDeviation
[SOURce<HW>]:BB:BTOoth:DTTest:FDRate
[SOURce<HW>]:BB:BTOoth:DTTest:MIMode
[SOURce<HW>]:BB:BTOoth:DTTest:NPPSet
[SOURce<HW>]:BB:BTOoth:DTTest:SPHase

Cloning the Group

// Create a clone of the original group, that exists independently
var dtTest2 = driver.Source.Bb.Btooth.DtTest.Clone();

Direct SCPI Members

bool Drift#
// SCPI: [SOURce<HW>]:BB:BTOoth:DTTest:DIRft
bool value = driver.Source.Bb.Btooth.DtTest.Drift;

No help available.


bool DttState#
// SCPI: [SOURce<HW>]:BB:BTOoth:DTTest:DTTState
bool value = driver.Source.Bb.Btooth.DtTest.DttState;

Activates the Dirty Transmitter Test. For EDR packets, the parameter sets apply for 20 packets each. For LE HDT packets, requires [:SOURce<hw>]:BB:BTOoth:HDT:CHEader:PFI FT0 | FT1.

dttState: 1 | ON | 0| OFF


int FdDeviation#
// SCPI: [SOURce<HW>]:BB:BTOoth:DTTest:FDDeviation
int value = driver.Source.Bb.Btooth.DtTest.FdDeviation;

Sets a frequency drift rate. A sine wave is used to drift the modulated Bluetooth signal around center frequency + carrier frequency offset. The maximum deviation reached during the drift equals the set frequency drift deviation.

fdDeviation: integer


double FdRate#
// SCPI: [SOURce<HW>]:BB:BTOoth:DTTest:FDRate
double value = driver.Source.Bb.Btooth.DtTest.FdRate;

Sets a frequency drift rate. A sine wave is used to drift the modulated Bluetooth signal around center frequency + carrier frequency offset with the set frequency drift rate.

fdRate: 0.3 KHz | 0.5 KHz | 1.6 KHz | 10 KHz


BtoModIdxModeEnum MiMode#
// SCPI: [SOURce<HW>]:BB:BTOoth:DTTest:MIMode
BtoModIdxModeEnum value = driver.Source.Bb.Btooth.DtTest.MiMode;

Determines standard or stable mode for the modulation index of dirty transmitter according to the Bluetooth core specification.

miMode: STANdard | STABle


BtoNumOfPackPerSetEnum Nppset#
// SCPI: [SOURce<HW>]:BB:BTOoth:DTTest:NPPSet
BtoNumOfPackPerSetEnum value = driver.Source.Bb.Btooth.DtTest.Nppset;

Specifies the number of packets per dirty transmitter set. Specifies the number of packets or CS steps per dirty transmitter set. Bluetooth mode / Channel type / Number of packets

  • BR + EDR / 50, 2, 1 packets

  • LE / Advertising, data / 50, 2, 1 packets

  • LE / Channel sounding / 50, 20, 18, 16, 14, 12, 10, 8, 6, 4, 2, 1 CS steps

numPack: NP50 | NP2 | NP1 | NP4 | NP6 | NP8 | NP10 | NP12 | NP14 | NP16 | NP18 | NP20


int Sphase#
// SCPI: [SOURce<HW>]:BB:BTOoth:DTTest:SPHase
int value = driver.Source.Bb.Btooth.DtTest.Sphase;

The command enters a start phase. The start phase applies to the sine wave that is used to drift the modulated Bluetooth signal. The drift is around the center frequency plus the carrier frequency offset.

sphase: integer


Subgroups