Source:Bb:Nr5G:Qckset:General#

SCPI Commands

[SOURce<HW>]:BB:NR5G:QCKSet:GENeral:CARDeply
[SOURce<HW>]:BB:NR5G:QCKSet:GENeral:CBW
[SOURce<HW>]:BB:NR5G:QCKSet:GENeral:CCTModel
[SOURce<HW>]:BB:NR5G:QCKSet:GENeral:CHRaster
[SOURce<HW>]:BB:NR5G:QCKSet:GENeral:CHSPacing
[SOURce<HW>]:BB:NR5G:QCKSet:GENeral:DUPLexing
[SOURce<HW>]:BB:NR5G:QCKSet:GENeral:ECPState
[SOURce<HW>]:BB:NR5G:QCKSet:GENeral:NCARier
[SOURce<HW>]:BB:NR5G:QCKSet:GENeral:SCSPacing

Cloning the Group

// Create a clone of the original group, that exists independently
var general2 = driver.Source.Bb.Nr5G.Qckset.General.Clone();

Direct SCPI Members

Nr5GcarDepEnum Cardeply#
// SCPI: [SOURce<HW>]:BB:NR5G:QCKSet:GENeral:CARDeply
Nr5GcarDepEnum value = driver.Source.Bb.Nr5G.Qckset.General.Cardeply;

Selects one of the frequency ranges, specified for 5G NR transmission.


Nr5GcbwEnum Cbw#
// SCPI: [SOURce<HW>]:BB:NR5G:QCKSet:GENeral:CBW
Nr5GcbwEnum value = driver.Source.Bb.Nr5G.Qckset.General.Cbw;

Selects the bandwidth of the node carrier.

qckSetChannelBw: BW5 | BW10 | BW15 | BW20 | BW25 | BW30 | BW35 | BW40 | BW45 | BW50 | BW60 | BW70 | BW80 | BW90 | BW100 | BW200 | BW400 | BW500 | BW800 | BW1600 | BW2000 | BW4000 | BW8000


bool CctModel#
// SCPI: [SOURce<HW>]:BB:NR5G:QCKSet:GENeral:CCTModel
bool value = driver.Source.Bb.Nr5G.Qckset.General.CctModel;

Creates a copy of a component carrier based on a test model configuration. Prerequisites for this command


AllChannelRasterEnum ChRaster#
// SCPI: [SOURce<HW>]:BB:NR5G:QCKSet:GENeral:CHRaster
AllChannelRasterEnum value = driver.Source.Bb.Nr5G.Qckset.General.ChRaster;

Sets the Channel Raster based on the set Deployment. If Deployment is set to FR1 ≤ 3GHz or FR1 > 3GHz the Channel Raster can be set to 15 kHz or 100 kHz. If Deployment is set to FR2-1 the Channel Raster is set to 60 kHz. If Deployment is set to FR2-2 the Channel Raster is set to 100 kHz. Channel Raster is not displayed when the Number of Carriers is shown inactive.

channelRaster: R15 | R60 | R100


int ChSpacing#
// SCPI: [SOURce<HW>]:BB:NR5G:QCKSet:GENeral:CHSPacing
int value = driver.Source.Bb.Nr5G.Qckset.General.ChSpacing;

Queries or sets the value for the Channel Spacing. It is by default automatically calculated by the set Channel Raster and the set Channel Bandwidth. The value can be manually adjusted, but is recalculated if the Channel Raster or the Channel Bandwidth is adjusted. Channel Spacing is not displayed when the Number of Carriers is shown inactive. In this case, it is used like Carrier Spacing equals 0.

channelSpacing: integer


EutraDuplexModeEnum Duplexing#
// SCPI: [SOURce<HW>]:BB:NR5G:QCKSet:GENeral:DUPLexing
EutraDuplexModeEnum value = driver.Source.Bb.Nr5G.Qckset.General.Duplexing;

Selects the duplexing mode.

qckSetDuplexing: TDD | FDD


bool EcpState#
// SCPI: [SOURce<HW>]:BB:NR5G:QCKSet:GENeral:ECPState
bool value = driver.Source.Bb.Nr5G.Qckset.General.EcpState;

Show if the extended cyclic prefix is enabled or disabled.

qssCsEcpState: 1 | ON | 0| OFF


int Ncarrier#
// SCPI: [SOURce<HW>]:BB:NR5G:QCKSet:GENeral:NCARier
int value = driver.Source.Bb.Nr5G.Qckset.General.Ncarrier;

Selects the number of carriers. Needed for carrier aggregation.

qckSetNumCarrier: integer


QucjSettingsScsAllEnum ScSpacing#
// SCPI: [SOURce<HW>]:BB:NR5G:QCKSet:GENeral:SCSPacing
QucjSettingsScsAllEnum value = driver.Source.Bb.Nr5G.Qckset.General.ScSpacing;

Sets the subcarrier spacing.


Subgroups