Source:Bb:Btooth:Pconfiguration#

SCPI Commands

[SOURce<HW>]:BB:BTOoth:PCONfiguration:ACKNowledgement
[SOURce<HW>]:BB:BTOoth:PCONfiguration:BDALap
[SOURce<HW>]:BB:BTOoth:PCONfiguration:BDANap
[SOURce<HW>]:BB:BTOoth:PCONfiguration:BDAUap
[SOURce<HW>]:BB:BTOoth:PCONfiguration:BYTEInterleaving
[SOURce<HW>]:BB:BTOoth:PCONfiguration:CODevice
[SOURce<HW>]:BB:BTOoth:PCONfiguration:DLENgth
[SOURce<HW>]:BB:BTOoth:PCONfiguration:DSFPacket
[SOURce<HW>]:BB:BTOoth:PCONfiguration:DWHitening
[SOURce<HW>]:BB:BTOoth:PCONfiguration:EIRPacketfollows
[SOURce<HW>]:BB:BTOoth:PCONfiguration:HFControl
[SOURce<HW>]:BB:BTOoth:PCONfiguration:HRINterleav
[SOURce<HW>]:BB:BTOoth:PCONfiguration:LFSWord
[SOURce<HW>]:BB:BTOoth:PCONfiguration:LTADdress
[SOURce<HW>]:BB:BTOoth:PCONfiguration:PFControl
[SOURce<HW>]:BB:BTOoth:PCONfiguration:PLENgth
[SOURce<HW>]:BB:BTOoth:PCONfiguration:SLAP
[SOURce<HW>]:BB:BTOoth:PCONfiguration:SNSValue
[SOURce<HW>]:BB:BTOoth:PCONfiguration:SRMode
[SOURce<HW>]:BB:BTOoth:PCONfiguration:VDATa

Cloning the Group

// Create a clone of the original group, that exists independently
var pconfiguration2 = driver.Source.Bb.Btooth.Pconfiguration.Clone();

Direct SCPI Members

BtoAckNldgmtEnum Acknowledgement#
// SCPI: [SOURce<HW>]:BB:BTOoth:PCONfiguration:ACKNowledgement
BtoAckNldgmtEnum value = driver.Source.Bb.Btooth.Pconfiguration.Acknowledgement;

Sets the ARQN bit of the packet header..

acknowledgement: NAK | ACK

  • NAK: Request to retransmit the previous payload.

  • ACK: Previous payload has been received successfully.


class BdaLap_Data

Structure for reading output parameters.

string BdaLap

numeric

int Bitcount

integer

BdaLap_Data BdaLap#
// SCPI: [SOURce<HW>]:BB:BTOoth:PCONfiguration:BDALap
BdaLap_Data value = driver.Source.Bb.Btooth.Pconfiguration.BdaLap;

Sets the lower address part of Bluetooth Device Address. The length of LAP is 24 bits or 6 hexadecimal figures.

For return value, see the help for BdaLap_Data structure arguments


class BdaNap_Data

Structure for reading output parameters.

string BdaNap

numeric

int Bitcount

integer

BdaNap_Data BdaNap#
// SCPI: [SOURce<HW>]:BB:BTOoth:PCONfiguration:BDANap
BdaNap_Data value = driver.Source.Bb.Btooth.Pconfiguration.BdaNap;

Enters the non-significant address part of Bluetooth Device Address. The length of NAP is 16 bits or 4 hexadecimal figures.

For return value, see the help for BdaNap_Data structure arguments


class BdaUap_Data

Structure for reading output parameters.

string BdaUap

numeric

int Bitcount

integer

BdaUap_Data BdaUap#
// SCPI: [SOURce<HW>]:BB:BTOoth:PCONfiguration:BDAUap
BdaUap_Data value = driver.Source.Bb.Btooth.Pconfiguration.BdaUap;

Enters the upper address part of Bluetooth Device Address. The length of UAP is 8 bits or 2 hexadecimal figures.

For return value, see the help for BdaUap_Data structure arguments


bool ByteInterleaving#
// SCPI: [SOURce<HW>]:BB:BTOoth:PCONfiguration:BYTEInterleaving
bool value = driver.Source.Bb.Btooth.Pconfiguration.ByteInterleaving;

No help available.


class CoDevice_Data

Structure for reading output parameters.

string CoDevice

numeric

int Bitcount

integer

CoDevice_Data CoDevice#
// SCPI: [SOURce<HW>]:BB:BTOoth:PCONfiguration:CODevice
CoDevice_Data value = driver.Source.Bb.Btooth.Pconfiguration.CoDevice;

A parameter received during the device discovery procedure, indicates the type of device and which types of service that are supported.

For return value, see the help for CoDevice_Data structure arguments


int Dlength#
// SCPI: [SOURce<HW>]:BB:BTOoth:PCONfiguration:DLENgth
int value = driver.Source.Bb.Btooth.Pconfiguration.Dlength;

Sets the payload data length in bytes.

dlength: integer


BtoDataSourForPckEnum DsfPacket#
// SCPI: [SOURce<HW>]:BB:BTOoth:PCONfiguration:DSFPacket
BtoDataSourForPckEnum value = driver.Source.Bb.Btooth.Pconfiguration.DsfPacket;

Selects the data source for the selected packet type.

dsfPacket: PEDit | ADATa

  • PED: Enables the Packet Editor. All packet fields can be configured individually.

  • ADAT: Fills the generated packets with the selected data source. Useful if predefined data contents are loaded with a data list file or the data contents of the packet are not of interest.


bool Dwhitening#
// SCPI: [SOURce<HW>]:BB:BTOoth:PCONfiguration:DWHitening
bool value = driver.Source.Bb.Btooth.Pconfiguration.Dwhitening;

Activates the Data Whitening.

dwhitening: 1 | ON | 0| OFF


YesNoStatusEnum EirPacketFollows#
// SCPI: [SOURce<HW>]:BB:BTOoth:PCONfiguration:EIRPacketfollows
YesNoStatusEnum value = driver.Source.Bb.Btooth.Pconfiguration.EirPacketFollows;

Indicates that an extended inquiry response packet can follow.

eirPacketFollow: YES | NO

  • YES: Indicates that EIR packet follows.

  • NO: Indicates that EIR packet does not follow.


BtoFlowCtrlEnum HfControl#
// SCPI: [SOURce<HW>]:BB:BTOoth:PCONfiguration:HFControl
BtoFlowCtrlEnum value = driver.Source.Bb.Btooth.Pconfiguration.HfControl;

The command sets the FLOW bit in the header. This bit indicates the start or stop of transmission of packets over the ACL logical transport.

hfControl: STOP | GO

  • STOP: Stops the other devices from transmitting data temporarily.

  • GO: Allows the other devices to transmit new data.


int HrInterleav#
// SCPI: [SOURce<HW>]:BB:BTOoth:PCONfiguration:HRINterleav
int value = driver.Source.Bb.Btooth.Pconfiguration.HrInterleav;

No help available.


class LfsWord_Data

Structure for reading output parameters.

string LapForSw

numeric

int Bitcount

integer

LfsWord_Data LfsWord#
// SCPI: [SOURce<HW>]:BB:BTOoth:PCONfiguration:LFSWord
LfsWord_Data value = driver.Source.Bb.Btooth.Pconfiguration.LfsWord;

Sets the lower address part (LAP) of the sync word for FHS packets. The length of LAP is 24 bits or 6 hexadecimal figures.

For return value, see the help for LfsWord_Data structure arguments


int LtAddress#
// SCPI: [SOURce<HW>]:BB:BTOoth:PCONfiguration:LTADdress
int value = driver.Source.Bb.Btooth.Pconfiguration.LtAddress;

The command enters the logical transport address for the header. Each Peripheral active in a piconet is assigned a primary logical transport address (LT_ADDR) . The all-zero LT_ADDR is reserved for broadcast messages.

ltAddress: integer


BtoFlowCtrlEnum PfControl#
// SCPI: [SOURce<HW>]:BB:BTOoth:PCONfiguration:PFControl
BtoFlowCtrlEnum value = driver.Source.Bb.Btooth.Pconfiguration.PfControl;

The command sets the FLOW bit in the payload (flow control per logical link) .

pfControl: STOP | GO

  • STOP: Indicates the stop of transmission of ACL packets before an additional amount of payload data is sent.

  • GO: Indicates the start of transmission of ACL packets after a new connection has been established.


int Plength#
// SCPI: [SOURce<HW>]:BB:BTOoth:PCONfiguration:PLENgth
int value = driver.Source.Bb.Btooth.Pconfiguration.Plength;

Sets the packet length in symbols.

plength: integer


bool Slap#
// SCPI: [SOURce<HW>]:BB:BTOoth:PCONfiguration:SLAP
bool value = driver.Source.Bb.Btooth.Pconfiguration.Slap;

Activates synchronization of the lower address part (LAP) of the sync word and Bluetooth device address.

state: 1 | ON | 0| OFF


int SnsValue#
// SCPI: [SOURce<HW>]:BB:BTOoth:PCONfiguration:SNSValue
int value = driver.Source.Bb.Btooth.Pconfiguration.SnsValue;

Sets the start value of the header SEQN bit. The SEQN bit is present in the header to filter out retransmissions in the destination. The signal generator is altering this bit automatically on consecutive frames, if a sequence length of at least 2 frames is set.

snsValue: integer


BtoScanReModeEnum SrMode#
// SCPI: [SOURce<HW>]:BB:BTOoth:PCONfiguration:SRMode
BtoScanReModeEnum value = driver.Source.Bb.Btooth.Pconfiguration.SrMode;

The command indicates the interval between two consecutive page scan windows, determines the behavior of the paging device.

srMode: R0 | R1 | R2

  • R0: The scan interval is equal to the scan window T w page scan (continuous nscan) and maximal 1.28s.

  • R1: The scan interval is maximal 1.28s.

  • R2: The scan interval is maximal 2.56s.


DataSourceBenum Vdata#
// SCPI: [SOURce<HW>]:BB:BTOoth:PCONfiguration:VDATa
DataSourceBenum value = driver.Source.Bb.Btooth.Pconfiguration.Vdata;

Selects the data source for the voice field.

vdata: ALL0 | ALL1 | PATTern | PN09 | PN11 | PN15 | PN16 | PN20 | PN21 | PN23 | DLISt


Subgroups