Source:Bb:Arbitrary:Cfr#

SCPI Commands

[SOURce<HW>]:BB:ARBitrary:CFR:ALGorithm
[SOURce<HW>]:BB:ARBitrary:CFR:CPBandwidth
[SOURce<HW>]:BB:ARBitrary:CFR:CSPacing
[SOURce<HW>]:BB:ARBitrary:CFR:DCFDelta
[SOURce<HW>]:BB:ARBitrary:CFR:FILTer
[SOURce<HW>]:BB:ARBitrary:CFR:FORDer
[SOURce<HW>]:BB:ARBitrary:CFR:ITERations
[SOURce<HW>]:BB:ARBitrary:CFR:OCFactor
[SOURce<HW>]:BB:ARBitrary:CFR:PFReq
[SOURce<HW>]:BB:ARBitrary:CFR:RCFactor
[SOURce<HW>]:BB:ARBitrary:CFR:SBANdwidth
[SOURce<HW>]:BB:ARBitrary:CFR:SFReq
[SOURce<HW>]:BB:ARBitrary:CFR:TBANdwidth
[SOURce<HW>]:BB:ARBitrary:CFR:[STATe]

Cloning the Group

// Create a clone of the original group, that exists independently
var cfr2 = driver.Source.Bb.Arbitrary.Cfr.Clone();

Direct SCPI Members

CfrAlgoEnum Algorithm#
// SCPI: [SOURce<HW>]:BB:ARBitrary:CFR:ALGorithm
CfrAlgoEnum value = driver.Source.Bb.Arbitrary.Cfr.Algorithm;
driver.Source.Bb.Arbitrary.Cfr.Algorithm = CfrAlgoEnum.CLFiltering;

Defines the algorithm for crest factor reduction.

arbCfrAlgorithm: CLFiltering | PCANcellation

  • CLFiltering: Clipping and filtering algorithm. This algorithm performs a hard clipping of the baseband signal. It is followed by a low pass filtering of the result in an iterative manner until the target crest factor is reached. You can define the settings of the filter that is used for the calculation.

  • PCANcellation: Peak cancelation algorithm. This algorithm subtracts Blackman windowed sinc pulses from the signal wherever the amplitude is above a defined threshold.


double CpBandwidth#
// SCPI: [SOURce<HW>]:BB:ARBitrary:CFR:CPBandwidth
double value = driver.Source.Bb.Arbitrary.Cfr.CpBandwidth;
driver.Source.Bb.Arbitrary.Cfr.CpBandwidth = 1.0;

Sets the cancellation pulse bandwidth for peak cancellation CFR algorithm.

arbCfrCancPulBw: float


double Cspacing#
// SCPI: [SOURce<HW>]:BB:ARBitrary:CFR:CSPacing
double value = driver.Source.Bb.Arbitrary.Cfr.Cspacing;
driver.Source.Bb.Arbitrary.Cfr.Cspacing = 1.0;

Sets the channel spacing, if method RsSmw.Source.Bb.Arbitrary.Cfr.Filter is set to SIMPle.

arbCfrChanSpac: float


double Dcfdelta#
// SCPI: [SOURce<HW>]:BB:ARBitrary:CFR:DCFDelta
double value = driver.Source.Bb.Arbitrary.Cfr.Dcfdelta;
driver.Source.Bb.Arbitrary.Cfr.Dcfdelta = 1.0;

Sets the value difference by which you want to change your crest factor.

arbCfrDcfDelta: float


CfrFiltModeEnum Filter#
// SCPI: [SOURce<HW>]:BB:ARBitrary:CFR:FILTer
CfrFiltModeEnum value = driver.Source.Bb.Arbitrary.Cfr.Filter;
driver.Source.Bb.Arbitrary.Cfr.Filter = CfrFiltModeEnum.ENHanced;

Selects which filter mode is used for the filtering.

arbCfrFilterMod: SIMPle | ENHanced


int Forder#
// SCPI: [SOURce<HW>]:BB:ARBitrary:CFR:FORDer
int value = driver.Source.Bb.Arbitrary.Cfr.Forder;
driver.Source.Bb.Arbitrary.Cfr.Forder = 1;

Sets the maximum filter order, if method RsSmw.Source.Bb.Arbitrary.Cfr.Filter is set to ENHanced.

arbCfrMaxFileOrder: integer


int Iterations#
// SCPI: [SOURce<HW>]:BB:ARBitrary:CFR:ITERations
int value = driver.Source.Bb.Arbitrary.Cfr.Iterations;
driver.Source.Bb.Arbitrary.Cfr.Iterations = 1;

Sets the number of iterations that are used for calculating the resulting crest factor. The iteration process is stopped when the desired crest factor delta is achieved by 0.1 dB.

arbCfrMaxIter: integer


double OcFactor#
// SCPI: [SOURce<HW>]:BB:ARBitrary:CFR:OCFactor
double value = driver.Source.Bb.Arbitrary.Cfr.OcFactor;

Queries the original crest factor of the waveform after the calculation of the resulting crest factor is completed. The original crest factor is calculated as an average over the whole waveform, including any idle periods that might be present in TDD waveforms.

arbCfroCrestFactor: float


double Pfreq#
// SCPI: [SOURce<HW>]:BB:ARBitrary:CFR:PFReq
double value = driver.Source.Bb.Arbitrary.Cfr.Pfreq;
driver.Source.Bb.Arbitrary.Cfr.Pfreq = 1.0;

Sets the passband frequency, if method RsSmw.Source.Bb.Arbitrary.Cfr.Filter is set to ENHanced. Frequency components lower than the passband frequency are passed through unfiltered.

arbCfrPassBandFreq: float


double RcFactor#
// SCPI: [SOURce<HW>]:BB:ARBitrary:CFR:RCFactor
double value = driver.Source.Bb.Arbitrary.Cfr.RcFactor;

Queries the resulting crest factor of the waveform after the calculations are completed. The resulting crest factor is calculated as an average over the whole waveform, including any idle periods that might be present in TDD waveforms.

arbCfrResCrestFactor: float


double Sbandwidth#
// SCPI: [SOURce<HW>]:BB:ARBitrary:CFR:SBANdwidth
double value = driver.Source.Bb.Arbitrary.Cfr.Sbandwidth;
driver.Source.Bb.Arbitrary.Cfr.Sbandwidth = 1.0;

Sets the signal bandwidth, if method RsSmw.Source.Bb.Arbitrary.Cfr.Filter is set to SIMPle. The value of the signal bandwidth should not be higher than the channel spacing (method RsSmw.Source.Bb.Arbitrary.Cfr.Cspacing) .

arbCfrSignalBw: float


double Sfreq#
// SCPI: [SOURce<HW>]:BB:ARBitrary:CFR:SFReq
double value = driver.Source.Bb.Arbitrary.Cfr.Sfreq;
driver.Source.Bb.Arbitrary.Cfr.Sfreq = 1.0;

Sets the stopband frequency of the filter, if method RsSmw.Source.Bb.Arbitrary.Cfr.Filter is set to ENHanced. Frequency components higher than the stopband frequency are filtered out by the lowpass filter.

arbCfrStopBandFreq: float


double Tbandwidth#
// SCPI: [SOURce<HW>]:BB:ARBitrary:CFR:TBANdwidth
double value = driver.Source.Bb.Arbitrary.Cfr.Tbandwidth;
driver.Source.Bb.Arbitrary.Cfr.Tbandwidth = 1.0;

Sets the transition bandwidth of the cancellation pulse for peak cancellation CFR algorithm.

ddaRbCfrTranBw: float


bool State#
// SCPI: [SOURce<HW>]:BB:ARBitrary:CFR:[STATe]
bool value = driver.Source.Bb.Arbitrary.Cfr.State;
driver.Source.Bb.Arbitrary.Cfr.State = false;

Enables the crest factor reduction calculation.

arbCfrState: 1 | ON | 0| OFF


Subgroups