Source:Sweep:Power#

SCPI Commands

[SOURce<HW>]:SWEep:POWer:AMODe
[SOURce<HW>]:SWEep:POWer:DWELl
[SOURce<HW>]:SWEep:POWer:MODE
[SOURce<HW>]:SWEep:POWer:POINts
[SOURce<HW>]:SWEep:POWer:RETRace
[SOURce<HW>]:SWEep:POWer:RUNNing
[SOURce<HW>]:SWEep:POWer:SHAPe

Cloning the Group

// Create a clone of the original group, that exists independently
var power2 = driver.Source.Sweep.Power.Clone();

Direct SCPI Members

PowerAttModeEnum Amode#
// SCPI: [SOURce<HW>]:SWEep:POWer:AMODe
PowerAttModeEnum value = driver.Source.Sweep.Power.Amode;
driver.Source.Sweep.Power.Amode = PowerAttModeEnum.AUTO;

Selects the power attenuator mode for the level sweep.

amode: NORMal | HPOWer

  • NORMal: Performs the level settings in the range of the built-in attenuator.

  • HPOWer: Performs the level settings in the high level range.


double Dwell#
// SCPI: [SOURce<HW>]:SWEep:POWer:DWELl
double value = driver.Source.Sweep.Power.Dwell;
driver.Source.Sweep.Power.Dwell = 1.0;

Sets the dwell time for a level sweep step.

dwell: float


AutoManStepEnum Mode#
// SCPI: [SOURce<HW>]:SWEep:POWer:MODE
AutoManStepEnum value = driver.Source.Sweep.Power.Mode;
driver.Source.Sweep.Power.Mode = AutoManStepEnum.AUTO;

Sets the cycle mode for the level sweep.

mode: AUTO | MANual | STEP

  • AUTO: Each trigger triggers exactly one complete sweep.

  • MANual: The trigger system is not active. You can trigger every step individually with the command [:SOURcehw]:POWer:MANual.The level value increases at each step by the value that you define with [:SOURcehw]:POWer:STEP[:INCRement]. Values directly entered with the command [:SOURcehw]:POWer:MANual are not taken into account.

  • STEP: Each trigger triggers one sweep step only. The level increases by the value entered with [:SOURcehw]:POWer:STEP[:INCRement].


int Points#
// SCPI: [SOURce<HW>]:SWEep:POWer:POINts
int value = driver.Source.Sweep.Power.Points;
driver.Source.Sweep.Power.Points = 1;

Sets the number of steps within the RF level sweep range.

points: integer


bool Retrace#
// SCPI: [SOURce<HW>]:SWEep:POWer:RETRace
bool value = driver.Source.Sweep.Power.Retrace;
driver.Source.Sweep.Power.Retrace = false;

Activates that the signal changes to the start frequency value while it is waiting for the next trigger event. You can enable this feature, when you are working with sawtooth shapes in sweep mode Single or External Single.

state: 1 | ON | 0| OFF


bool Running#
// SCPI: [SOURce<HW>]:SWEep:POWer:RUNNing
bool value = driver.Source.Sweep.Power.Running;

Queries the current sweep state.

state: 1 | ON | 0| OFF


SweCyclModeEnum Shape#
// SCPI: [SOURce<HW>]:SWEep:POWer:SHAPe
SweCyclModeEnum value = driver.Source.Sweep.Power.Shape;
driver.Source.Sweep.Power.Shape = SweCyclModeEnum.SAWTooth;

Determines the waveform shape for a frequency sweep sequence.

shape: SAWTooth | TRIangle


Subgroups