Source:LfOutput:Sweep:Frequency#

SCPI Commands

[SOURce<HW>]:LFOutput:SWEep:[FREQuency]:DWELl
[SOURce<HW>]:LFOutput:SWEep:[FREQuency]:MODE
[SOURce<HW>]:LFOutput:SWEep:[FREQuency]:POINts
[SOURce<HW>]:LFOutput:SWEep:[FREQuency]:RETRace
[SOURce<HW>]:LFOutput:SWEep:[FREQuency]:RUNNing
[SOURce<HW>]:LFOutput:SWEep:[FREQuency]:SHAPe
[SOURce<HW>]:LFOutput:SWEep:[FREQuency]:SPACing

Cloning the Group

// Create a clone of the original group, that exists independently
var frequency2 = driver.Source.LfOutput.Sweep.Frequency.Clone();

Direct SCPI Members

double Dwell#
// SCPI: [SOURce<HW>]:LFOutput:SWEep:[FREQuency]:DWELl
double value = driver.Source.LfOutput.Sweep.Frequency.Dwell;
driver.Source.LfOutput.Sweep.Frequency.Dwell = 1.0;

Sets the dwell time for each frequency step of the sweep.

dwell: float


AutoManStepEnum Mode#
// SCPI: [SOURce<HW>]:LFOutput:SWEep:[FREQuency]:MODE
AutoManStepEnum value = driver.Source.LfOutput.Sweep.Frequency.Mode;
driver.Source.LfOutput.Sweep.Frequency.Mode = AutoManStepEnum.AUTO;

Sets the cycle mode of the LF sweep.

mode: AUTO | MANual | STEP

  • AUTO: Performs a complete sweep cycle from the start to the end value when a trigger event occurs.The dwell time determines the time period until the signal switches to the next step.

  • MANual: Performs a single sweep step when a manual trigger event occurs.The trigger system is not active. To trigger each frequency step of the sweep individually, use the command [:SOURcehw]:LFOutput:FREQuency:MANual.

  • STEP: Each trigger command triggers one sweep step only.The frequency increases by the value set with the coammnds:[:SOURcehw]:LFOutput:SWEep[:FREQuency]:STEP[:LINear] (linear spacing) [:SOURcehw]:LFOutput:SWEep[:FREQuency]:STEP:LOGarithmic(logarithmic spacing)


int Points#
// SCPI: [SOURce<HW>]:LFOutput:SWEep:[FREQuency]:POINts
int value = driver.Source.LfOutput.Sweep.Frequency.Points;
driver.Source.LfOutput.Sweep.Frequency.Points = 1;

Sets the number of steps in an LF sweep. For information on how the value is calculated and the interdependency with other parameters, see “Correlating parameters in sweep mode”

points: integer


bool Retrace#
// SCPI: [SOURce<HW>]:LFOutput:SWEep:[FREQuency]:RETRace
bool value = driver.Source.LfOutput.Sweep.Frequency.Retrace;
driver.Source.LfOutput.Sweep.Frequency.Retrace = false;

Activates that the signal changes to the start frequency value while it is waiting for the next trigger event. You can enable this feature, when you are working with sawtooth shapes in sweep mode Single or External Single.

state: 1 | ON | 0| OFF


bool Running#
// SCPI: [SOURce<HW>]:LFOutput:SWEep:[FREQuency]:RUNNing
bool value = driver.Source.LfOutput.Sweep.Frequency.Running;

Queries the current status of the LF frequency sweep mode.

state: 1 | ON | 0| OFF


SweCyclModeEnum Shape#
// SCPI: [SOURce<HW>]:LFOutput:SWEep:[FREQuency]:SHAPe
SweCyclModeEnum value = driver.Source.LfOutput.Sweep.Frequency.Shape;
driver.Source.LfOutput.Sweep.Frequency.Shape = SweCyclModeEnum.SAWTooth;

Sets the cycle mode for a sweep sequence (shape) .

shape: SAWTooth | TRIangle


SpacingEnum Spacing#
// SCPI: [SOURce<HW>]:LFOutput:SWEep:[FREQuency]:SPACing
SpacingEnum value = driver.Source.LfOutput.Sweep.Frequency.Spacing;
driver.Source.LfOutput.Sweep.Frequency.Spacing = SpacingEnum.LINear;

Selects linear or logarithmic sweep spacing.

spacing: LINear | LOGarithmic


Subgroups